Front drive axle of the car Chevrolet Tahoe 2 and 3

8.25« reducer, switchable axle, early models
8.25" gearbox, switchable axle, early models. 1 - axle shaft; 2 - axle shaft seal; 3 - axle bearing; 4 - bridge beam; 5 - thrust washer of the clutch gear; 6 -...

8.25« reducer, switchable axle, late models
8.25" gearbox, switchable axle, late models. 1 - axle shaft; 2 - spacer of the drive gear of the reducer; 3 - bearing of the drive gear of the reducer; 4 -...

8.25« gearbox, fixed axle, late models
Reducer 8.25 inch, non-switchable bridge, late models. 1 - axle shaft; 2 - spacer of the drive gear of the reducer; 3 - bearing of the drive gear of the...

9.25« reducer, switchable axle
Reducer 9,25 inches, the disconnected bridge. 1 - axle shaft; 2 - axle shaft seal; 3 - axle bearing; 4 - bridge beam; 5 - thrust washer of the clutch gear; 6 -...

8.25« reduction, fixed axle, early models
8.25" reduction, fixed axle, early models. 1 - axle shaft, 2 - axle shaft seal, 3 - axle shaft bearing, 4 - axle beam, 5 - axle shaft retaining ring, 6 - axle...

Checking the oil level
1. Raise the car. 2. Adjust body position so that it is level. 3. If installed, remove the gearbox guard. 4. Check the front axle for oil leaks. Carry out...

Transmission oil change
1. Raise the car. 2. Adjust body position so that it is level. 3. If installed, remove the gearbox guard. 4. Check the front axle for oil leaks. Carry out...

Breather hose — removal and installation
Early gear models 8.25" and all gearbox models 9.25" 1. Raise the car. 2. If installed, remove the gear guard. Attention: remember the route of the hose. 3....

Breather hose fitting — removal and installation
Early gear models 8.25" and reducer 9.25" 1. Raise the car. 2. Disconnect the breather hose from the fitting on the gearbox housing. 3. Turn out the union....

Bridge engagement drive
Withdrawal 1. Raise the car. 2. If installed, remove the gear guard. 3. Disconnect drive connector (1) (reducer 8.25") or (3) (reducer 9.25"). 4. Remove the...

Fork, oil seal and deflector of the drive gear of the gearbox
Withdrawal 1. Raise the car. 2. Remove the front wheels. 3. Remove the brake calipers. 4. If installed, remove gear guard. 5. Mark the relative position of the...

Front Axle Reducer — 2500 Series
Withdrawal 1. Turn the steering wheel to the left until it stops. 2. Raise the vehicle. 3. Drive the jack over the back of the frame. 4. Remove the motor...

Front Axle Reducer — 1500 Series
Withdrawal 1. Raise the car. 2. Remove the cross member of the lower control arm. 3. Drain the oil from the gearbox housing. 4. Disconnect the wires of the...

Fixed Axle Shaft and Beam — 8.25« Reducer
Removal - left side 1. Raise the car. 2. Drain the oil from the front axle reduction case. 3. Remove the anti-roll bars (early models) or suspension damper...

Axle shaft and beam of the disconnected bridge — gearboxes 8.25 and 9.25
Withdrawal 1. Raise the car. 2. Drain the oil from the front axle gearbox. 3. Disconnect the axle engagement drive wiring connector. 4. Release the axle...