Lighting and lamps (since 2007) of car Chevrolet Tahoe 2 and 3

Removal and installation of the stoplight switch
Models with adjustable pedal height 1. Disconnect the connector. 2. Remove the latch (4). 3. Remove the brake light switch (2) off axis (1) and disconnect the...

Removing and installing the brake pedal position sensor
1. Remove the knee brace. 2. Remove the mounting block cover. 3. Disconnect the connector (1). 4. Remove the bolts (2). Tightening torque 9 Nm. 5. Remove the...

Removal and installation of the lighting control switch
1. Remove switch panel (1). 2. Release the clips and remove the light control switch, backlight rheostat and interior light switch assembly (2).

Removal and installation of the light sensor
1. Remove the upper trim of the instrument panel (1). 2. Rotate and remove the light sensor (2). 3. Disconnect the connector. 4. Install in the reverse order...

Removal and installation of a lamp of illumination of salon
1. Remove the cover (1). 2. Remove the lamps (2). 3. Install in the reverse order of removal.

Removal and installation of a lamp of local illumination
1. Remove the cover (1). 2. Remove the lamps (2). 3. Install in the reverse order of removal.

Removal and installation of a lamp of illumination of a footboard
1. Using a slotted screwdriver, press the latch and remove the footrest lamp (1) from the side mirror. 2. Disconnect the connector. 3. Remove cartridge (2). 4....

Removal and installation of a lamp of illumination of an aperture deri
1. Gently pull the front of the door trim towards you. 2. Using a slotted screwdriver, remove the doorway light. 3. Remove the cover (1). 4. Install in the...

Removal and installation of a back lamp of illumination of salon
1. Using a slotted screwdriver, press the latch and remove the cover (1). 2. Remove the rear interior lamp (2). 3. Disconnect the connector. 4. Install in the...

Removal and installation of headlights
Escalade (halogen headlights) 1. Remove the two front fender liner mounting screws. 2. Disconnect the two washer hose clamps (left headlight only). 3. Open the...

Removal and installation of a ballast of a gas-discharge headlight
1. Remove the headlight. 2. Loosen the three screws (1). 3. Remove the headlight ballast (2). 4. Install in the reverse order of removal.

Replacing headlight bulbs
Escalade 1. Remove the headlight. 2. Remove the cover (1). 3. Remove the lamp (2). 4. Disconnect the connector (3). 5. Install in the reverse order of removal....

Removal and installation of fog lights
Tahoe, Avalanche 1. Remove fender liner. 2. Detach the clips (2). 3. Detach the retainer (3). 4. Disconnect the connector (1). 5. Remove the fog lamp (4). 6....

Replacing lamps in the daytime lighting system
Escalade 1. Remove the headlight. 2. Remove the cover (1). 3. Remove the lamp (2). 4. Install in the reverse order of removal. Yukon 1. Remove the headlight....

Removal and installation of the repeater of turn (Escalade)
1. Remove fender liner. 2. Disconnect the connector (1). 3. Squeeze the latches (2) and remove the turn signal repeater (3). 4. Install in the reverse order of...

Replacing the front lamp
Tahoe, Avalanche 1. Remove the headlight. 2. Remove cartridge (1). 3. Remove the lamp (2). 4. Install in the reverse order of removal. Yukon 1. Remove the...

Turn Signal/Parking Light Bulb Replacement
Tahoe, Avalanche 1. Remove the headlight. 2. Disconnect the connector. 3. Remove the lamp (1). 4. Install in the reverse order of removal. Yukon 1. Remove the...

Removal and installation of an additional brake light
Yukon 1. Remove finishing of an additional stoplight. 2. Loosen the nuts (1). 3. Remove the additional brake light (2). 4. Install in the reverse order of...

Removal and installation of license plate lamps
Escalade 1. Remove two screws (1). 2. Remove the cover (2). 3. Remove the lamp (3). 4. Install in the reverse order of removal. Yukon 1. Remove the cover (1)....

Removal and installation of the rear combination lamp
Escalade 1. Open the back door. 2. Loosen the screws (1). 3. Detach the clips (2), by releasing the guides (3). 4. Disconnect the connector (4). 5. Remove the...

Replacing lamps in combination lamp
Escalade 1. Remove the rear combination lamp. 2. Disconnect the connector and remove the reversing light bulb (1). 3. Install in the reverse order of removal....