Lighting and lamps (until 2007) car Chevrolet Tahoe 2 and 3

Removal and installation of the lighting control switch
1. Remove a facet of finishing of a combination of devices. 2. Use a slotted screwdriver to release the latches. 3. Disconnect the connectors. 4. Remove the...

Removal and installation of the switch of fog lamps
1. Remove a facet of finishing of a combination of devices. 2. Remove the fog light switch from the instrument panel. 3. Disconnect the connector. 4. Install...

Fog lamp switch and interior lamps
1. Remove a facet of finishing of a combination of devices. 2. Remove the fog light switch and interior light switch from the instrument panel. 3. Disconnect...

Removal and installation of the fog lamp switch
1. Remove a facet of finishing of a combination of devices. 2. Remove the optional switch panel. 3. Disconnect the connector. 4. Remove the fog lamp switch. 5....

Removal and installation of the stoplight switch
1. Remove the latch (1) and disconnect the connector (3). 2. Detach the retainer (4). 3. Remove the brake light switch (2). 4. Install in the reverse order of...

Removal and installation of the switch of the corrector of headlights
1. Remove a facet of finishing of a combination of devices. 2. Remove the headlight range control switch from the instrument panel. 3. Disconnect the...

Removal and installation of the light sensor
1. Remove the top trim of the instrument panel. 2. Disconnect the connector (1) from the sensor. 3. Turn the sensor a quarter of a turn and remove it. 4....

Removal and installation of the relay-interrupter of indexes of turn
1. Remove the knee brace. 2. Remove the relay-interrupter of indexes of turn. 3. Install in the reverse order of removal.

Removal and installation of the relay of system of illumination in the daytime
1. Open the cover of the mounting block in the engine compartment (2) and body (1), by unfastening the fasteners (3). 2. Remove the daytime lighting relay. 3....

Removal and installation of headlights
Tahoe Attention: halogen lamps get very hot during operation. If the surface of the lamp becomes dirty, it will cause the surface of the halogen lamp to heat...

Removal and installation of discharge headlights
Attention: To prevent electric shock, replace gas discharge lamps in a dry room, dry your hands thoroughly before starting work. When the headlights are turned...

Removal and installation of a fog lamp
Type 1 1. Disconnect the connector. 2. Detach the lamp retainer from the bracket. 3. Turn away an adjusting bolt and a spring. 4. Remove the fog lamp from the...

Fog lights and daytime running lights (Avalanche)
1. Put the car on a lift. 2. Disconnect the connector. Attention: halogen lamps get very hot during operation. If the surface of the lamp becomes dirty, it...

Replacing bulbs in fog lights
1. Disconnect the connector. 2. Turn the cartridge counterclockwise and remove the bulb. 3. Install in the reverse order of removal.

Fog lamp adjustment
1. Make sure all components are installed on the vehicle and all work on the vehicle has been stopped. 2. Place the unladen vehicle on a level, level surface....

Removal and installation of the forward indicator of turn
1. Turn the light control switch to position "OFF". 2. Remove the headlight. 3. Disconnect the clamps and remove the front turn signal. 4. Disconnect the...

Front turn signal and tail light (Avalanche)
1. Detach the latch (1). 2. Detach the retainer (2). 3. Remove the front turn signal and front marker (5) and disconnect the connector (3). 4. Rotate chucks...

Removal and installation of the combined lantern
Type 1 1. Turn the light control switch to position "OFF". 2. Lower tailgate. 3. Turn away two screws and remove the back combined lantern. 4. Replace the lamp...

Removal and installation of a fog lamp
1. Remove the bolt (2) from the fog light bracket. Tightening torque 25 Nm. 2. Disconnect the connector from the fog lamp. 3. Remove the fog light (1). 4....

Replacing the fog light bulb
1. Remove two screws (2) and remove diffuser (1) from the foundation (3). 2. Turn the bulb counterclockwise and remove it. 3. Install in the reverse order of...

Removal and installation of an additional brake light
Tahoe type 1 1. Turn the light control switch to position "OFF". 2. Loosen the screws. Tightening torque 2 Nm. 3. Remove an additional stoplight. 4. Disconnect...

Removal and installation of a lamp of illumination of license plate
Type 1 1. Turn the light control switch to position "OFF". 2. Remove the license plate light and remove the cover. 3. Remove the lamp. 4. Install in the...

Removal and installation of a lamp of illumination of a motor compartment
1. Disconnect the connector. 2. Press a latch and remove a lamp of illumination of a motor compartment. 3. Using a slotted screwdriver, remove the cover. 4....

Removal and installation of a lamp of illumination of an aperture of a door
1. Slide the lamp forward and use a slotted screwdriver to remove it. 2. Rotate the chuck and remove it. 3. Remove the bulb from the socket. 4. Install in the...

Removal and installation of a lamp of illumination of a footboard
1. Using a slotted screwdriver, remove the footrest lamp. 2. Disconnect the connector. 3. Remove two screws. 4. Remove the lamp. 5. Install in the reverse...

Removal and installation of a lamp of illumination of salon
1. Using a slotted screwdriver, remove the cover. 2. Remove a paw of illumination of salon. 3. Disconnect the connector. 4. Remove the lamp. 5. Install in the...

Removal and installation of a lamp of illumination of a ware box
1. Turn the light control switch to position "OFF". 2. Open the glove box lid. 3. Press on latches and remove a lamp of illumination of a ware box. 4....

Removal and installation of a lamp of illumination of a cosmetic mirror
1. Lower the sun visor. 2. Lift the lid of the vanity mirror. 3. Using a slotted screwdriver, press the lamp cover latch. 4. Remove a plafond of a lamp of...

Removal and installation of a lamp of illumination of an ashtray
1. Turn the light control switch to position "OFF". 2. Remove the knee brace. 3. Remove the glove box. 4. Remove the ashtray. 5. Remove the bulb with socket...