Vehicle lighting and instrumentation Chevrolet Niva 1
Wires and fuses
The electrical equipment is made according to a single-wire circuit - the negative terminals of the sources and consumers of electricity are connected to the...
The electrical equipment is made according to a single-wire circuit - the negative terminals of the sources and consumers of electricity are connected to the...
Mounting block
Most fuses and auxiliary relays are located in a separate mounting block (pic. 7-1), built into the instrument panel on the left side of the steering column....
Most fuses and auxiliary relays are located in a separate mounting block (pic. 7-1), built into the instrument panel on the left side of the steering column....
Ignition switch
On cars «Chevrolet Niva» the ignition switch type 2123-3704005 is used with an anti-theft locking device, a blocking against restarting the starter without...
On cars «Chevrolet Niva» the ignition switch type 2123-3704005 is used with an anti-theft locking device, a blocking against restarting the starter without...
Lighting and light signaling: device features
Headlights On cars, a headlight unit is used that combines low beam and high beam headlights (with single filament lamps) and direction indicators. In...
Headlights On cars, a headlight unit is used that combines low beam and high beam headlights (with single filament lamps) and direction indicators. In...
Headlight adjustment
The direction of the light beams of the headlights should be such that the road in front of the car is well lit, and the drivers of oncoming vehicles are not...
The direction of the light beams of the headlights should be such that the road in front of the car is well lit, and the drivers of oncoming vehicles are not...
Fog lamp adjustment
Headlight adjustment is carried out using optical instruments. If they are not there, then the adjustment can be carried out on a horizontal platform using a...
Headlight adjustment is carried out using optical instruments. If they are not there, then the adjustment can be carried out on a horizontal platform using a...
Lamp replacement
Block headlights Before changing the bulbs in the headlamp, remove the protective cover 4 (see fig. 7-27), which is fixed with a wire holder 3. To replace the...
Block headlights Before changing the bulbs in the headlamp, remove the protective cover 4 (see fig. 7-27), which is fixed with a wire holder 3. To replace the...
Headlight range control motor
The headlights are corrected by a gearmotor installed inside the headlight unit. The design of the gearmotor is non-separable and in case of a malfunction it...
The headlights are corrected by a gearmotor installed inside the headlight unit. The design of the gearmotor is non-separable and in case of a malfunction it...
Understeering's shifter
The steering column switch consists of a connector fixed with a clamp on the steering gear shaft bracket, and two switches. The left switch turns on the...
The steering column switch consists of a connector fixed with a clamp on the steering gear shaft bracket, and two switches. The left switch turns on the...
Headlight relay
To turn on the headlights, relays of type 904.3747-10 are used, installed in the mounting block. Relay switch-on voltage at temperature (23±5) °С is not more...
To turn on the headlights, relays of type 904.3747-10 are used, installed in the mounting block. Relay switch-on voltage at temperature (23±5) °С is not more...
Relay-interrupter for direction indicators and alarms
Relay-breaker K3 (see fig. 7-25) type 493.3747 or 495.3747, installed in the mounting block, is used to create an intermittent light signal for direction...
Relay-breaker K3 (see fig. 7-25) type 493.3747 or 495.3747, installed in the mounting block, is used to create an intermittent light signal for direction...
Data for checking the electric motor
Rated shaft speed when the motor is loaded with an impeller, min -1 - 2600-2800 Consumed current at the specified load and speed, A, no more than — 25 To drive...
Rated shaft speed when the motor is loaded with an impeller, min -1 - 2600-2800 Consumed current at the specified load and speed, A, no more than — 25 To drive...
Sound signal
On cars, a sound signal of type 20.3721 is installed. It is located in the engine compartment and is attached to the radiator grille mounting bracket. The...
On cars, a sound signal of type 20.3721 is installed. It is located in the engine compartment and is attached to the radiator grille mounting bracket. The...
Features of the windshield wiper device
The windshield wiper kit consists of a wiper drive, levers and brushes. The scheme of inclusion of a cleaner is shown in fig. 7-39. The cleaner has three modes...
The windshield wiper kit consists of a wiper drive, levers and brushes. The scheme of inclusion of a cleaner is shown in fig. 7-39. The cleaner has three modes...
Removal and installation of a cleaner of a windscreen
Cleaner repair consists mainly in editing deformed rods and levers or replacing them with new ones. It is recommended to replace a defective gearmotor with a...
Cleaner repair consists mainly in editing deformed rods and levers or replacing them with new ones. It is recommended to replace a defective gearmotor with a...
Data for checking the windshield wiper gearmotor
Speed of the gearmotor shaft at a supply voltage of 13.5 V, a load torque of 2 Nm and an ambient temperature (25±10) °C, min -1 : first (small) — 39-50 second...
Speed of the gearmotor shaft at a supply voltage of 13.5 V, a load torque of 2 Nm and an ambient temperature (25±10) °C, min -1 : first (small) — 39-50 second...
Windshield Wiper Relay
The connection diagram of the relay outputs is shown in fig. 7-39. Pic. 7-39. Windshield wiper and washer connection diagram: 1 - windshield washer motor; 2 -...
The connection diagram of the relay outputs is shown in fig. 7-39. Pic. 7-39. Windshield wiper and washer connection diagram: 1 - windshield washer motor; 2 -...
Rear window cleaner
The rear window cleaner consists of a gearmotor, a lever and a brush. Laying the lever with a brush right in the direction of the car. The motor reducers of...
The rear window cleaner consists of a gearmotor, a lever and a brush. Laying the lever with a brush right in the direction of the car. The motor reducers of...
Removal and installation of a cleaner of back glass
Repair of the cleaner consists mainly in editing the levers or replacing them with new ones. It is recommended to replace a defective gearmotor with a new one....
Repair of the cleaner consists mainly in editing the levers or replacing them with new ones. It is recommended to replace a defective gearmotor with a new one....
Features of the heater fan motor device
The scheme of inclusion of the electric motor is shown in fig. 7-41. Pic. 7-41. Scheme of switching on the electric motor of the heater fan and heating...
The scheme of inclusion of the electric motor is shown in fig. 7-41. Pic. 7-41. Scheme of switching on the electric motor of the heater fan and heating...
Data for checking the heater fan motor
Shaft speed when the motor is loaded with an impeller at a voltage of 12 V and temperature (25±10) °С, min -1 - 3000 Consumed current at the specified load and...
Shaft speed when the motor is loaded with an impeller at a voltage of 12 V and temperature (25±10) °С, min -1 - 3000 Consumed current at the specified load and...
External mirror control system
Exterior mirrors with electric drive are installed on cars «Chevrolet Niva» in a variant. The control scheme of the motor-reducers of the exterior mirrors is...
Exterior mirrors with electric drive are installed on cars «Chevrolet Niva» in a variant. The control scheme of the motor-reducers of the exterior mirrors is...
Heating system for exterior mirrors and rear window
The diagram of the heating system for exterior mirrors and rear window is shown in fig. 7-41 Pic. 7-41. Scheme of switching on the electric motor of the heater...
The diagram of the heating system for exterior mirrors and rear window is shown in fig. 7-41 Pic. 7-41. Scheme of switching on the electric motor of the heater...
Front seat heating system
Front seat heaters are installed on cars «Chevrolet Niva» in a variant. The scheme of inclusion of heaters is given in fig. 7-43. Pic. 7-43. The scheme of...
Front seat heaters are installed on cars «Chevrolet Niva» in a variant. The scheme of inclusion of heaters is given in fig. 7-43. Pic. 7-43. The scheme of...
Front electric windows
Cars «Chevrolet Niva» equipped with power windows for lowering and raising the windows of the front doors. In the window regulator mechanism, instead of the...
Cars «Chevrolet Niva» equipped with power windows for lowering and raising the windows of the front doors. In the window regulator mechanism, instead of the...
Data for checking the gearmotor of the electric windows of the front doors
The frequency of rotation of the gearmotor shaft at idle at the supply voltage (13,5±0,1) In and ambient temperature (25±10) °C, min -1 : 56-90 Current...
The frequency of rotation of the gearmotor shaft at idle at the supply voltage (13,5±0,1) In and ambient temperature (25±10) °C, min -1 : 56-90 Current...
Door lock system
The system is installed on parts of manufactured cars and is designed to simultaneously block the locks of all doors when locking the left front door with a...
The system is installed on parts of manufactured cars and is designed to simultaneously block the locks of all doors when locking the left front door with a...
Data for checking the gearmotor of the door lock system
The force developed by the actuating element at the supply voltage (13±0,1) At and at ambient temperature (25±10) °C, N, not less: — 30 Consumed current at the...
The force developed by the actuating element at the supply voltage (13±0,1) At and at ambient temperature (25±10) °C, N, not less: — 30 Consumed current at the...
Features of the instrument cluster device
The vehicles are fitted with an electronic instrument cluster. It includes a speedometer, a counter of the total and daily mileage of the car (odometer) with...
The vehicles are fitted with an electronic instrument cluster. It includes a speedometer, a counter of the total and daily mileage of the car (odometer) with...
Removal and installation, checking the instrument cluster
To remove the instrument cluster, do the following: disconnect the wire from the terminal «minus» battery; remove the instrument panel shield as described in...
To remove the instrument cluster, do the following: disconnect the wire from the terminal «minus» battery; remove the instrument panel shield as described in...
Checking sensors of control devices
Coolant temperature gauge sensor. The sensor has a variable resistor that changes its resistance depending on the temperature of the coolant. The data for...
Coolant temperature gauge sensor. The sensor has a variable resistor that changes its resistance depending on the temperature of the coolant. The data for...
Immobilizer
immobilizer (car anti-theft system APS-6) designed to prevent unauthorized starting of the engine. The composition of the immobilizer is shown in fig. 7-47....
immobilizer (car anti-theft system APS-6) designed to prevent unauthorized starting of the engine. The composition of the immobilizer is shown in fig. 7-47....
Power package remote control system «Norma»
On cars of complete sets 55 and 34, a remote control system for electric accessories is installed "Norm" (SDUEP). SDUEP "Norm" intended for: remote locking /...
On cars of complete sets 55 and 34, a remote control system for electric accessories is installed "Norm" (SDUEP). SDUEP "Norm" intended for: remote locking /...
Power package control unit — removal and installation
Withdrawal Place the vehicle in the workplace, brake with the parking brake, turn off the ignition and disconnect the terminal «minus» from the battery. Pic....
Withdrawal Place the vehicle in the workplace, brake with the parking brake, turn off the ignition and disconnect the terminal «minus» from the battery. Pic....
Replacing the battery of the remote control key
In the key with remote control, fig. 7-54, a CR2032 type lithium battery is installed, the initial supply voltage of which is 3V. Pic. 7-54. Key with remote...
In the key with remote control, fig. 7-54, a CR2032 type lithium battery is installed, the initial supply voltage of which is 3V. Pic. 7-54. Key with remote...
This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Share information:
- General information
- Vehicle device
- User manual
- Maintenance
- Power unit
- Engine repair
- Cooling system
- Lubrication system
- Power and exhaust system
- Transmission
- Clutch
- Car gearbox
- Transfer case
- Cardan gear
- Rear axle
- Front axle
- Chassis
- Suspension and shock absorbers
- Steering
- Brake system
- Body
- Exterior (external elements)
- Interior (internal elements)
- Ventilation and heating
- Electrical equipment
- Power devices
- Lighting and appliances
ChevyMan.ru © 2017-2024 · Mobile version · Feedback · Site search · Interesting to read · Sitemap: EN BG BY UA RS HR RO PL SK HU
Aveo 2003-2008 · Aveo 2006-2011 · Aveo 2012-2018 · Captiva 2006-2018 · Cruze 2008-2016 · Lacetti 2002-2009 · Lanos 2002-2009 · Niva 2002-2016 · Tahoe 1992-2000 · Tahoe 2000-2014 · Lumina 1 1989-1994 · Trailblazer 1 2001-2008 ·
Aveo 2003-2008 · Aveo 2006-2011 · Aveo 2012-2018 · Captiva 2006-2018 · Cruze 2008-2016 · Lacetti 2002-2009 · Lanos 2002-2009 · Niva 2002-2016 · Tahoe 1992-2000 · Tahoe 2000-2014 · Lumina 1 1989-1994 · Trailblazer 1 2001-2008 ·